Products Guide
H5003 Compact PCM Mux
Product Overview
H5003 device is a new multi-function integrated service access device. It has two standard E1 transmission interfaces and provides 30 channels of voice and asynchronous data access,supporting many voice services including FXO, FXS, magneto, and 4-wire andRS232/RS422 asynchronous data. This device provides two E1 transmission directions and can work at 1+1 protection mode.
H5003 device can be used for point to point connection,it can also internetwork with our company’s PCM device, e.g.CO device H9MO-LMXE+.V2 and realize point to multipoint connecton.H5003 device can be equipped with monitoring system.Through monitoring system you can monitor the running status of device in real time and conduct fault location and reallocation of time slots. Main console is connected to monitored device through Ethernet interface, which is convenient to be added to network management of higher level.
Features
l Support ADM or TM modes, the ADM mode supports two transmission direction, and TM provides 1+ 1 transmission protection
l 2 standardE1 interfaces, complying with ITU-T G.703 recommendation
l Voice interface supports 30 channels of two-wire phone (FXO/FXS/Hotline/2100Hz Magneto), or 22 channels of two-wire phone and 8 channels of four-wire voice and 4 channels of E/M signaling and complies with ITU-TG.711 and G.713 recommendations
l RS232 asynchronous data support 30 channels at maximum, RS422 asynchronous data support 8 channels at m aximum
l A abundan tof LEDs on the panel for convenient operation and fault diagnosis
l ADM supports 64kbit/s monitoring function, and each E1 can select a 64kbit/s time slot as monitoring channel
l 19 inches1U standard chassis, which is small volume and save space
l -48V DC power supply, or -48V DC/100~240V wide-range AC dual mode power supply
l Support bottom program and FPGA program online update.
Specifications
E1 Interface | ||
Item | Standards | |
Bit rate | 2.048Mbps±50ppm | |
Line code | HDB3 G.703 | |
Connector | BNC,RJ-48C | |
The input impedance | 75Ω,120Ω | |
Frame structure | ITU-T G.704,G.706 | |
Compression rule | ITU-T G.711 A rule | |
Electrical level | 75Ω: ±2.37V±10% 150Ω:±3.0V±10% | |
Interface count | 2 | |
Ethernet Interface |
| |
Item | Standards | |
Interface mode | 10/100 Base-T Ethernet MDI interface | |
Connector | RJ45 | |
Interface count | 1 | |
Speech path interface and signaling | ||
Exchange side | ||
Item | Standards | |
Off hook impedance | <500ω> | |
Hang impedance | >10KΩ | |
User side | ||
Item | Standards | |
The loop impedance | ≤2000Ω | |
Free circuit voltage | ≤50V | |
The loop current | 25mA | |
Off hook threshold | 8mA | |
Polarity reversal delay | <50ms> | |
Dial |
| |
Off hook delay | Dial pulse single pulse distortion<5ms<> | |
In band audio dialing total distortion meet the voice interface characteristics. | ||
Off hook delay | <100ms> | |
Ringing Current | ||
FXS Ringing Current Generator | ||
Item | Standards | |
Frequency | 25Hz±3Hz | |
Amplitude | 75V±5Vrms | |
Ringing current delay | <50ms> | |
Total output power | ≤10W(chassis unit) | |
FXO Ringing Current Detection | ||
Item | Standards | |
Amplitude range | Minimum 38Vrms | |
Voice Interface | ||
Item | Standards | |
Impedance | 600Ω or 3-component duplex impedance. | |
Audio range | 300~3400Hz | |
Coding law | ITU-T G.711 A law | |
2-wire interface level | 2-wire sending 0dBr±0.5dBr | |
2-wire receiving -3.5dBr±0.5dBr | ||
Return loss | 300~600Hz >12dB | |
600~3400Hz >15dB | ||
Frequency response | 300~3400Hz complying with ITU G.713 | |
Idle channel noise | ≤-65dBm0p | |
Gain | -45dBm0~+3dBm0(error less than ±0.5dB) | |
Total SNR | Complying with ITU-T G.713 template | |
Voice capacity | 30 channels of 2-wire telephone(FXO/FXS/hotline/2011Hz magneto),or 22 channels of 2-wire telephone + eight channels of 4-wirewire voice + four channels of E/M signalings | |
Hotline | ||
Item | Standards | |
Loop impedance | <2000ω>(including telephone) | |
Idle circuit voltage | <50v> | |
Loop current | 25mA | |
Off-hook threshold | 8mA | |
Voice interface specifications | Please refer to Voice Interface | |
4-wirewire Voice |
| |
Item | Standards | |
Impedance | 600Ω | |
Audio range | 300~3400Hz | |
Coding law | 300 | |
Return loss | 300~600Hz >12dB | |
600~3400Hz >15dB | ||
Frequency response | 300~3400Hz complying with ITU G.713 | |
Idle channel noise | ≤-65dBm0p | |
Gain | -45dBm0~+3dBm0(error less than ±0.5dB) | |
Total SNR | Complying with ITU-T G.713 template | |
4-wire interface level | Factory default 4-wire sending 0dBr±0.5dBr | |
Factory default 4-wire receiving 0dBr±0.5dBr | ||
Attenuator adjustment range | 4-wire sending (A/D) attenuation:-16.3~+8.9dBr | |
4-wire receiving (A/D) attenuation:-20.6~+4.3dBr | ||
Adjustment precision | 0.1dB | |
Carrier Magneto Interface | ||
Item | Standards | |
Audio | Interface level | 2-wire sending 0dBr±0.5dBr |
2-wire receiving -3.5dBr±0.5dBr | ||
Signaling | Ringing current detection | Minimum 20Vrms |
Signaling method | In-band -2100Hz tone | |
2100Hz signal generator | Amplitude:-6dBm0±1dB | |
Frequency:2100Hz±5Hz | ||
Signaling detection | Amplitude range: not less than -17dBm | |
Frequency range:2100Hz±50Hz | ||
Asynchrous Data Interface | ||
Item | Standards | |
Interface level | Complying with RS-232/V.28 standard or RS-422/V.11 standard | |
Interface rate | ≤14.4kbit/s | |
Interface number | Each board provides two channels | |
Clock | ||
Item | Standards | |
Clock source | Internal clock,E1 line clock | |
Physical/Electrical | ||
Size | 45mm*290mm*440mm(H/D/W) | |
Power supply(AC) | 100~265V,50/60Hz | |
Power supply(DC) | -48V(-72V~ -36V) | |
Power consumption | ≤50W | |
Operation temperature | -10~55℃ | |
Storage temperature | -20~65℃ | |
Humidity | 0-90%RH(non-condensing) |
Typical Application
l Point topoint Network
l StarNetwork
l Along theline Network